Check the phone and head before you clamp anything
The QS-72T is a long Arca-compatible quick shoe with a foldaway central column that clamps a smartphone up to 85mm wide. That width limit is the first thing to check: measure your phone, case included, before you buy or fit it. If your phone is wider than 85mm with the case on, this clamp is not the right mount.
The second check is the head. The QS-72T is described as compatible with any brand's Arca-compatible head, and the supplied list names the Vanguard PH-114V plus VEO tripod heads, Alta BH, Alta GH, Alta PH-32, Alta PH-31, TBH, BBH, GH-200 and GH-300T. If your head is not Arca-compatible, the shoe will not slide into the clamp, so confirm the clamp type first.
Mount the smartphone on the QS-72T
- Open the clamp and seat the phone: Use the foldaway central column to open the smartphone clamp, place the phone against the clamp faces, and close it so the phone is held across its width. The clamp is rated for phones up to 85mm wide.
- Slide the shoe into the Arca head: With the phone clamped, slide the quick shoe into the Arca-compatible head from the top or rear, depending on your head's clamp design, then tighten the head's clamp. The long plate gives you fore-and-aft travel for balancing the phone over the head.
- Add a light or microphone to the cold shoe: The top of the smartphone clamp has a cold shoe mount for accessories such as a light or microphone, or any other accessory using a VEO CSM adaptor. Slide the accessory foot in and tighten its own locking collar or screw where it has one.
- Use the side 1/4" thread for a support arm: A 1/4" thread hole on the side of the shoe lets you attach more accessories using a suitable support arm, such as the VEO TSA. This is the mounting point to use when the cold shoe is already taken or when the accessory needs to sit off to the side.
What the QS-72T gives you on an Arca head
- QS-72T Long Arca Compatible Quick Shoe For Smartphone: The Vanguard QS-72T Quick Shoe is an Arca-compatible quick release plate with a foldaway central column that attaches a smartphone up to 85mm wide to any Arca-compatible tripod head. This is the core fit decision: the 85mm clamp width and Arca-compatible head are both required for the phone setup to work.

QS-72T Long Arca Compatible Quick Shoe For Smartphone - QS-72T Long Arca Compatible Quick Shoe For Smartphone: It includes a 1/4" camera screw and anti-slip rubber pads, so it can also be used with a camera or spotting scope on an Arca-compatible head. The same shoe can carry a camera or scope, which is why the plate is worth keeping on the head when you switch between phone and camera.
- QS-72T Long Arca Compatible Quick Shoe For Smartphone: The top of the smartphone clamp has a cold shoe mount for accessories such as a light or microphone, or any other accessory using a VEO CSM adaptor. It turns the phone mount into a small rig without adding a separate cage or bracket.
Switch between phone, camera and scope without swapping plates
The QS-72T is not only a phone clamp. With the 1/4" camera screw and anti-slip rubber pads, it can also hold a camera or spotting scope on the same Arca-compatible head. That makes it a useful bridge between smartphone shooting and your normal camera kit.
The practical benefit is speed. If you have the same number of quick release shoes as cameras or scopes, you can change kit without transferring the plate each time. For a phone-plus-camera setup, that means one shoe for the phone clamp and another for the camera, both sliding into the same head.
When you fit the shoe to a camera base, the supplied information lists four ways to tighten it: by hand using the D-ring, with an Allen key, with a coin, or with a screwdriver. Use whichever you have to hand, but check the camera is secure before you let go.
Checkpoints before you trust the rig
- Phone width: Confirm the phone, with its case, is within the 85mm clamp width. A phone that is too wide will not seat properly.
- Head compatibility: Confirm the head is Arca-compatible. The supplied list covers Vanguard PH-114V, VEO tripod heads, Alta BH, Alta GH, Alta PH-32, Alta PH-31, TBH, BBH, GH-200 and GH-300T, plus other brands' Arca-compatible heads.
- Clamp tension: Tighten the head's Arca clamp after sliding the shoe in, and check the phone clamp is closed on the phone before you let go.
- Accessory security: Check any cold shoe accessory or side-arm accessory is locked down before you move the tripod.
What the supplied information does not settle
The supplied record does not give a maximum load for the smartphone clamp, a phone thickness range, or a list of specific phone models. It also does not state whether the cold shoe has a locking pin, or give a maximum weight for accessories on the cold shoe or the side 1/4" thread. Treat those as things to confirm with the accessory maker or Vanguard before hanging heavy gear on the shoe.
The record also does not describe a step-by-step procedure for adjusting the foldaway central column beyond its role in clamping the phone. If you are unsure how much force the clamp needs, start gently and check the phone is held before tilting the head.


